Diplomová práce je zaměřená na možnosti vytlačování polymerních směsí s mikrofibrilární fázovou strukturou pomocí vytlačovací hlavy se semihyperbolickým sbíhavým kanálem. Za tímto účelem byly připraveny tři druhy směsí polyetylenu a polypropylenu ve hmotnostním poměru 80/20, 70/30, 60/40. Tyto směsi spolu s čistými materiály byly popsány z hlediska tokového chování. Výsledná struktura a vlastnosti vytlačených pásků byly následně studovány pomocí širokoúhlé rentgenografie, diferenciální snímací kalorimetrie, elektronové mikroskopie a tahových zkoušek. Práce ukazuje, že tvorba mikrofibrilární fázové struktury je dosažena ve všech směsích, nezávisle na mísících poměrech a zpracovatelských podmínkách. Nicméně, struktura a vlastnosti těchto mikrofibrilárních kompozitů jsou výrazně ovlivněné podmínkami míchání a vytlačování.
Anotace v angličtině
The master thesis is focused on the possibilities of microfibrillar-phase formation in polymer blends during extrusion through a die with semihyperbolic-converging channel. For these purposes, three polyethylene/polypropylene blends with the mixing ratios (wt./wt.) 80/20, 70/30 and 60/40 were prepared. These blends as well as pure materials were described from the rheological point of view. Final structure and properties of extruded blends were examined using wide-angle X-ray scattering, differential scanning calorimetry, electron microscopy and tensile testing. It is demonstrated that the formation of microfibrillar-phase morphology is achieved in all the blends, independent of their mixing ratios and processing conditions used. However, the structure and properties of these microfibrillar-phase composites are strongly influenced by mixing/extrusion parameters.
Klíčová slova
polyetylen, polypropylen, in-situ kompozit
Klíčová slova v angličtině
polyethylene, polypropylene, in-situ composite
Rozsah průvodní práce
81 s.
Jazyk
AN
Anotace
Diplomová práce je zaměřená na možnosti vytlačování polymerních směsí s mikrofibrilární fázovou strukturou pomocí vytlačovací hlavy se semihyperbolickým sbíhavým kanálem. Za tímto účelem byly připraveny tři druhy směsí polyetylenu a polypropylenu ve hmotnostním poměru 80/20, 70/30, 60/40. Tyto směsi spolu s čistými materiály byly popsány z hlediska tokového chování. Výsledná struktura a vlastnosti vytlačených pásků byly následně studovány pomocí širokoúhlé rentgenografie, diferenciální snímací kalorimetrie, elektronové mikroskopie a tahových zkoušek. Práce ukazuje, že tvorba mikrofibrilární fázové struktury je dosažena ve všech směsích, nezávisle na mísících poměrech a zpracovatelských podmínkách. Nicméně, struktura a vlastnosti těchto mikrofibrilárních kompozitů jsou výrazně ovlivněné podmínkami míchání a vytlačování.
Anotace v angličtině
The master thesis is focused on the possibilities of microfibrillar-phase formation in polymer blends during extrusion through a die with semihyperbolic-converging channel. For these purposes, three polyethylene/polypropylene blends with the mixing ratios (wt./wt.) 80/20, 70/30 and 60/40 were prepared. These blends as well as pure materials were described from the rheological point of view. Final structure and properties of extruded blends were examined using wide-angle X-ray scattering, differential scanning calorimetry, electron microscopy and tensile testing. It is demonstrated that the formation of microfibrillar-phase morphology is achieved in all the blends, independent of their mixing ratios and processing conditions used. However, the structure and properties of these microfibrillar-phase composites are strongly influenced by mixing/extrusion parameters.
Klíčová slova
polyetylen, polypropylen, in-situ kompozit
Klíčová slova v angličtině
polyethylene, polypropylene, in-situ composite
Zásady pro vypracování
The Master thesis will be focused on the possibilities of microfibrillar-phase formation in polymer blends during flow through extrusion die with semihyperbolic-converging channel. For these purposes, several blends of polyethylene and polypropylene will be prepared and used. Final structure of extruded blends will be examined at several structural levels using X-ray scattering, differential scanning calorimetry, electron microscopy and light microscopy. Finally, the effect of phase morphology on mechanical properties will be studied.
Zásady pro vypracování
The Master thesis will be focused on the possibilities of microfibrillar-phase formation in polymer blends during flow through extrusion die with semihyperbolic-converging channel. For these purposes, several blends of polyethylene and polypropylene will be prepared and used. Final structure of extruded blends will be examined at several structural levels using X-ray scattering, differential scanning calorimetry, electron microscopy and light microscopy. Finally, the effect of phase morphology on mechanical properties will be studied.
Seznam doporučené literatury
TJONG, S.C. Mater. Sci. Eng. R 2003, vol. 41, p. 1.
TAYLOR, G.I. Proc. R. Soc. 1934, vol. A146, p. 501.
GRACE, H.P. Chem. Eng. Commun. 1983, vol. 14, p. 225.
MCHUGH, A.J. J. Appl. Polym. Sci. 1975, vol. 19, p. 125.
TUREK, D.E., SIMON, G.P. Polymer 1993, vol. 34, p. 2750.
MONTICCIOLO, A., CASSAGNAU, P., MICHEL A. Polym. Eng. Sci. 1998, vol. 38, p. 1882.
EHRENSTEIN, G.W., MAERTIN, C. Kunststoffe, 1985, vol. 75, p. 20.
OBADAL, M., ČERMÁK, R., STOKLASA, K., HABROVÁ, V. Plast. Rubb. Compos. Macromol. Eng. 2004, vol. 33, p. 295.
VARGA, J., BREINING, A., EHRENSTEIN, G.W. Int. Polym. Process. 2000, vol. 15, p. 53.
LI, X., CHEN, M., HUANG, Y., LIN, G., ZHAO, S., LIAO, B., WANG, C., CONG, G. Adv. Polym. Technol. 1997, vol. 16, p. 331.
Seznam doporučené literatury
TJONG, S.C. Mater. Sci. Eng. R 2003, vol. 41, p. 1.
TAYLOR, G.I. Proc. R. Soc. 1934, vol. A146, p. 501.
GRACE, H.P. Chem. Eng. Commun. 1983, vol. 14, p. 225.
MCHUGH, A.J. J. Appl. Polym. Sci. 1975, vol. 19, p. 125.
TUREK, D.E., SIMON, G.P. Polymer 1993, vol. 34, p. 2750.
MONTICCIOLO, A., CASSAGNAU, P., MICHEL A. Polym. Eng. Sci. 1998, vol. 38, p. 1882.
EHRENSTEIN, G.W., MAERTIN, C. Kunststoffe, 1985, vol. 75, p. 20.
OBADAL, M., ČERMÁK, R., STOKLASA, K., HABROVÁ, V. Plast. Rubb. Compos. Macromol. Eng. 2004, vol. 33, p. 295.
VARGA, J., BREINING, A., EHRENSTEIN, G.W. Int. Polym. Process. 2000, vol. 15, p. 53.
LI, X., CHEN, M., HUANG, Y., LIN, G., ZHAO, S., LIAO, B., WANG, C., CONG, G. Adv. Polym. Technol. 1997, vol. 16, p. 331.
Přílohy volně vložené
-
Přílohy vázané v práci
-
Převzato z knihovny
Ano
Plný text práce
Přílohy
Posudek(y) oponenta
Hodnocení vedoucího
Záznam průběhu obhajoby
Oponent: doc. Ing. Petr Ponížil, Ph.D.
Otázky: podrobně viz příloha Protokolu o státní závěrečné zkoušce - Posudek oponenta DP
Členové komise:
U některých grafů nemáte popis os. Můžete nám tyto popisy os dodatečně říci?
Člen komise: doc. Ing. Vladimír Klepal, CSc.
Otázka: Čím jsou ovlivněny výsledky měření - vzory nebo zvolenou metodikou?
Jak je ovlivněna krystalizace metodou přípravy vzorů?
Člen komise: doc. Ing. Karel Stoklasa, CSc.
Otázka: Co je fibrilární část a co je lamelární část u vzorků - snímky TEM?
Jaká je struktura a čím je tvořena struktura šiš-kebab?